Stel uw vraag of bel mij terug a.u.b. (Have a Question or call back request)

Beschikbare fastATE modules.

 

YAV9JTAG 128 DIOs JTAG BSRU

1.270,00

YAV9JTAG 128 DIOs JTAG BSRU Image

Fully open general application JTAG I/O Interface
• Board integration into the platform, therefore can be used for multiple fixtures
• Up to 128 tristate DIOs, 1V8/2V5/3V3 (5V tolerant), 8x 8bits AIs, 8x 8bits AOs and 2 RS232/UART ports (Set of two boards)
• Built-in USB 2.0 to JTAG interface
• Configurable JTAG chain till 40Mhz
• Connector input compatible with XJAG USB-JTAG Interface
• Automatic interface selection according to the fixture
• Working voltage automatic selection for each block of 16 DIOs
• Commercial software or self made (BSDL language)
• Professional mass connection Virginia Panel Quadra paddle
• “Black box” testing for non JTAG boards
• High quality standard fixture interface VPC connector
• Fully expandable
• Boundary Scan I/O as a shared resource of your ATE

YAV9JTAG modules supported by JTAG Technologies

Catalogue overview available YAVModules

Download the Catalogue.

Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.

Production test is an obvious area in which the use of boundary-scan yields tremendous returns. Automatic test program generation and fault diagnostics using boundary-scan software products and the lack of expensive fixture requirements can make the entire test process very economical. The YAV9JTAG and YAV9JTAH are BSRU (Boundary Scann Resource Units) and has been developed for products that contain BGA IC’s, edge connect-ors and digital interfaces that are not visible from the boundary-scan chain, and provide a low cost alternative to expensive digital pin electronics.

With the YAV9JTAG boards set, you will improve reliability of your systems by increasing analogue, digital and interface test coverage, reducing your debug time by enhanced fault isolation.

The use of its build-in USB/JTAG interface as a JTAG probe, you have open all the hardware Boundary Scann possibilities, from BS component pins reading and writing to SDRAM/SRAM/Flash Memory Test and programming.

Your custom test fixtures will be less expensive due to the reduction of hardware and wiring complexity.

Applications
• Hardware regressing testing, BGA’s and board test
• High speed IOs
• JTAG Probe
• Boundary Scann Test
• Flash, FPGAs and CPLDs programming

Categorie:
YAVModules
Subcategorie:
Boundary Scan

YAV9JTAG 128 DIOs JTAG BSRU

1.270,00

YAV9JTAG 128 DIOs JTAG BSRU Image

Fully open general application JTAG I/O Interface
• Board integration into the platform, therefore can be used for multiple fixtures
• Up to 128 tristate DIOs, 1V8/2V5/3V3 (5V tolerant), 8x 8bits AIs, 8x 8bits AOs and 2 RS232/UART ports (Set of two boards)
• Built-in USB 2.0 to JTAG interface
• Configurable JTAG chain till 40Mhz
• Connector input compatible with XJAG USB-JTAG Interface
• Automatic interface selection according to the fixture
• Working voltage automatic selection for each block of 16 DIOs
• Commercial software or self made (BSDL language)
• Professional mass connection Virginia Panel Quadra paddle
• “Black box” testing for non JTAG boards
• High quality standard fixture interface VPC connector
• Fully expandable
• Boundary Scan I/O as a shared resource of your ATE

YAV9JTAG modules supported by JTAG Technologies

Catalogue overview available YAVModules

Download the Catalogue.

Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.

Production test is an obvious area in which the use of boundary-scan yields tremendous returns. Automatic test program generation and fault diagnostics using boundary-scan software products and the lack of expensive fixture requirements can make the entire test process very economical. The YAV9JTAG and YAV9JTAH are BSRU (Boundary Scann Resource Units) and has been developed for products that contain BGA IC’s, edge connect-ors and digital interfaces that are not visible from the boundary-scan chain, and provide a low cost alternative to expensive digital pin electronics.

With the YAV9JTAG boards set, you will improve reliability of your systems by increasing analogue, digital and interface test coverage, reducing your debug time by enhanced fault isolation.

The use of its build-in USB/JTAG interface as a JTAG probe, you have open all the hardware Boundary Scann possibilities, from BS component pins reading and writing to SDRAM/SRAM/Flash Memory Test and programming.

Your custom test fixtures will be less expensive due to the reduction of hardware and wiring complexity.

Applications
• Hardware regressing testing, BGA’s and board test
• High speed IOs
• JTAG Probe
• Boundary Scann Test
• Flash, FPGAs and CPLDs programming


het bouwen van een testsysteem met 6TL is als werken met LEGO.

FastATE van 6TL is een concept voor engineers die zelf een testsysteem willen bouwen. Voor engineers is er niets leuker dan zelf te ontwikkelen., maar dit is niet altijd verstandig. Vaak ontbreekt de basiskennis en ervaring en ontstaat er een groot gevaar in de vele valkuilen te stappen bij het ontwikkelen van een testsysteem. Doe waar u goed in bent en laat u ondersteunen en voorlichten over zaken die u normaal gesproken nooit doet.

Bedrijfspresentatie 6TL Engineering.

fastATE is een techniek die u als engineer in staat stelt een ideaal test systeem te construeren zonder het gevaar van de vele valkuilen. Het fastATE concept bestaat uit vele modules waardoor de opbouw van een testsysteem net zo eenvoudig wordt als iets bouwen met Lego. Een overzicht van een groot deel van de beschikbare modules vindt u hieronder in een lijst. Als u zich voor de vraag gesteld ziet:  BUILD OR BUY een deel of uw gehele testsystem, lees dan eerst onze informatiebrief over dit onderwerp.

Onze specialisten komen graag bij u langs om uit te leggen waarom fastATE ook voor u de beste oplossing is.
Maak eventueel gebruik van de SEND message tab, rechts onder om ons direct te contacteren.

Hieronder vindt u een opsomming van alle beschikbare fastATE modules, deze zijn sorteerbaar op categorie en productgroep. Het kan even duren voor de lijst zichtbaar wordt.
Voor prijsinformatie kunt u contact met ons opnemen of een login code aanvragen en op onderstaande pagina de prijzen zelf bekijken.


Sample modular solutions created using FastATE technology from 6TL.


Romex hi-res-logo-transp

Print Friendly, PDF & Email