YAVPacks general information; Click here!

Compact, high performance and low cost testing solution
Very Low cost engineering and wiring
100% re-usable!
Direct mains Voltage Handling: AC/DC measurements up to 500V
Ethernet control through CAN bus Gateway (Master Script Edition Sw, based on excel sheet as Option; P/N H68002500)
CAN bus control (Phi6 Drivers)
USB port (Printer or firmware upload)

Applications:
Stand Alone Smart Fixture for FCT and ISP
PC controlled SmartFixtures
Cell test in Burn-in or Endurance test systems
Switching Units for on-board testing
Data Aquisition
Thermal test (Headsinks thermal resistance)

Thanks to the YAVPACKs, a low cost tester can be implemented. Basic measurements can be performed with the YPB, thanks to the combination of the smart measurement module (YAV90MMU) and other switching modules.

The YPB is featuring a 4-slot Chassis, and includes:

– YAV90MMU – Ethernet to CAN
– YAV90CIN
– 24Vdc Power Supply
– MMI
– Ethernet crossover cable
– Power cord
– Manual 730021Ex

The YAVPack can be also controlled trhough CAN, thanks to:
– Phi6 Drivers
– CAN Cable
– USB-CAN Interface

Easy to use Test program sequencer capable to handle up to 1000 test steps and running in MS EXcel.

Thanks to the YAVPACKs, a low cost tester can be implemented, only with the fixture and the YAVPACK inside.
Basic measurements can be performed with the YAVPACK, thanks to the combination of the smart measurement unit and some switching. To get the best performance, the user can program the test steps, download them into the YAVPACK and start testing.
To implement the test executive, excel can be used thanks to this license. The MMU Master Script Edition software enables the user to write test sequences and transfer operational test step codes to the YAV90MMU (always in the YAVPACK).
The test sequence is based in MS Excel sheet, so that every opeartor can use it.
A maximum of 1000 test steps can be defined.

See below a video showing how to program the test sequence using Microsoft Excel

This MMI (Man Machine Interface) can be directly connected to the YAV90MMU or a YAVPack through CanBus

It can also be build inside a so called 6TL02 SmartFixture to be used as the operator interface.

The RED and Green lighted push buttons in combination with two LED Arrows can be used to start and stop a test program, indicate pass or fail, indicate the direction to turn when you need to adjust a potentiometer, buss and flash to indicate an operator intervention.

A two segment display indicates the test step that is currently activated.

Bundle of 3 units

There are two ways to do the wiring between the test fixture and a YAVPack:
– DIRECT WIRING: For software debugging, test of prototypes or for single use fixture, the user can connect patchcords from the receiver modules in the YAVPack to the pin plate in the fixture. This solution is low cost and quick.

– ITA FRAME: When you plan to use several probe plates (Bed of needles) with the same YAVPack, using the YAVPack ITA frame, enables the user to plug/unplug all the connections at the same time and the probe plate change operation can be done easily and without risk (strain relief available with the ITA frame).

The Table Top SmartFixture MMI

4 digit display to indicate the actual test step
5 input keypad for communication
Status LEDs indicating pass/fail, testing, idle, or operator intervention.

The Table Top MMI, will be used for the operator to control the test execution, as well as to see the test step that is being processed.
The 800808E MMI, is prepared to be plugged into the X1 connector from the YAVPack and placed wherever the user wishes, for the best ergonomic operation of the test station.
The Table Top MMI can show up to 1000 test steps, thanks to featured 4-digit display.