24-Bit Digital I/O Controlling logic circuits is a common requirement. The two modules above are easy to program, both at the "bit" and "byte" levels. The DIO-MATE supports standard TTL logic, while the OPTO-MATE uses photo-couplers to iso- late inputs and outputs. The DIO-MATE and DIO-MATEII offer 24 & 48 bits (respectively). Programming allows setting for port direction and logic level (for both individual bits or bytes). You can also enable weak pull-ups on the inputs…
24-Bit Digital I/O Controlling logic circuits is a common requirement. The two modules above are easy to program, both at the ’bit’ and ’byte’ levels. The DIO-MATE supports standard TTL logic, while the OPTO-MATE uses photo-couplers to iso- late inputs and outputs. The DIO-MATE and DIO-MATEII offer 24 & 48 bits (respectively). Programming allows setting for port direction and logic level (for both individual bits or bytes). You can also enable weak pull-ups on the inputs…
Download the Catalogue. [youtube https://www.youtube.com/watch?v=YTRr1BOvVPg?rel=0] 5x (1�8) Mux. + 1�2 + 2x Pass Through 30VAC/DC, 10W Max Max. carry current 500mA CAN bus controlled Reflective Form A The YAV91501 uses so called reflective switches that are not terminated. This version has no 50 Ohm resistors implemented for the unused ports, therefore it might reflect the RF signals back, this effect can potentially damage the RF equipment. An advantage of not terminating these ports is that the…
Features ? 5 independent multiplexer connected in tree mode 1 to 4 ? 2 Direct steps from ITA to instrumentation or up to 20 points on tree con-figuration Download the Catalogue. Applications ? High frequency up to 2,5 GHz signal commutation by means of configurable tree mode connection. Input Characteristics Maximum switching voltage 30VAC / DC Maximum switching capacity 10W @900MHz Maximum carry current 0.50 A Maximum RF power 10W @900MHz Initial DC path resistance <…
Download the Catalogue. [youtube https://www.youtube.com/watch?v=YTRr1BOvVPg?rel=0] YAV90058A ITA 8-Channels Ethernet adapter for YAV90058
Download the Catalogue. [youtube https://www.youtube.com/watch?v=YTRr1BOvVPg?rel=0] ? Suitable for 1GigaBit Ethernet, LVDS, RS232, USB and Telephony switching applications ? CAN bus controlled wide differential Bandwidth multiplexer for Differential Signals ? 100R Differential Impedance ? Requiered Quadrapaddle Module 510 151 105 (ITA) or ITA Interface boards
Download the Catalogue. [youtube https://www.youtube.com/watch?v=YTRr1BOvVPg?rel=0] ? 80 DIOs ? 8 AIs ? 8 AOs ? Compatible with all JTAG suppliers
Fully open general application JTAG I/O Interface ? Board integration into the platform, therefore can be used for multiple fixtures ? Up to 128 tristate DIOs, 1V8/2V5/3V3 (5V tolerant), 8x 8bits AIs, 8x 8bits AOs and 2 RS232/UART ports (Set of two boards) ? Built-in USB 2.0 to JTAG interface ? Configurable JTAG chain till 40Mhz ? Connector input compatible with XJAG USB-JTAG Interface ? Automatic interface selection according to the fixture ? Working voltage automatic…
Description ? 12 Relays 8A 250V ? Current measurement ? Double tripaddle contact per connection. ? Plug-in terminals for power supplies and loads ? Enable contact for each relay ? Power supply of 24VDC only ? Automatic identification of the module ? National Instruments LabView drivers Download the Catalogus [youtube https://www.youtube.com/watch?v=YTRr1BOvVPg?rel=0] Applications ? Power Input/outputs with current measurement in tests systems using VPC receivers
Description ? 12 Relays 8A 250V ? Double tripaddle contact per connection. ? Plug-in terminals for power supplies and loads ? Enable contact for each relay ? Power supply of 24VDC only ? Automatic identification of the module ? National Instruments LabView drivers Download the Catalogue Applications ? Power Input/outputs in tests systems using VPC receivers. The YAV90PIN board is designed to cover the need to control the available power supplies in a test system to…
? Interface for universal In-System Programmers up to 8 simultaneous targets in parallel ? Isolation relay barrier / De-multiplexer module to increase to up 32 devices ? Keeps extremely short wires for keeping signal integrity ? I2C and SPI communications interface Download the Catalog The YAV90ISP standalone in-site programming interface has been designed to simplify and standardize the wiring in testing platforms that use fast ISP and/or I2C / SPI data communications. All active lines, included…
? Test up to 16 LEDs (Low to High Brightness) simultaneously ? Fiber optic input channels (POF) ? 1 optical calibration RGB LED output ? Wave lengh (420?650 nm) and luminance (Intensity) readout ? 24VDC single power supply ? OK/NOK comparator threshold settings ? VPC receiver fixture compatible ? CAN bus control ? Built in power supply ? Self module identifier ? National Instruments LabView drivers Download the Catalogue. The YAV90CLR module is the most cost…
