YAV90058 Data Communications MUX

Download the Catalogue. [youtube https://www.youtube.com/watch?v=YTRr1BOvVPg?rel=0] ? Suitable for 1GigaBit Ethernet, LVDS, RS232, USB and Telephony switching applications ? CAN bus controlled wide differential Bandwidth multiplexer for Differential Signals ? 100R Differential Impedance ? Requiered Quadrapaddle Module 510 151 105 (ITA) or ITA Interface boards

Lees verderYAV90058 Data Communications MUX

YAV91500 2,5 GHz 15 relays switching-multiplexer board 50ohm

Features ? 5 independent multiplexer connected in tree mode 1 to 4 ? 2 Direct steps from ITA to instrumentation or up to 20 points on tree con-figuration Download the Catalogue. Applications ? High frequency up to 2,5 GHz signal commutation by means of configurable tree mode connection. Input Characteristics Maximum switching voltage 30VAC / DC Maximum switching capacity 10W @900MHz Maximum carry current 0.50 A Maximum RF power 10W @900MHz Initial DC path resistance <…

Lees verderYAV91500 2,5 GHz 15 relays switching-multiplexer board 50ohm

YAV91501 2,5GHz 50Ohm SMB Multiplexer (not terminated)

Download the Catalogue. [youtube https://www.youtube.com/watch?v=YTRr1BOvVPg?rel=0] 5x (1�8) Mux. + 1�2 + 2x Pass Through 30VAC/DC, 10W Max Max. carry current 500mA CAN bus controlled Reflective Form A The YAV91501 uses so called reflective switches that are not terminated. This version has no 50 Ohm resistors implemented for the unused ports, therefore it might reflect the RF signals back, this effect can potentially damage the RF equipment. An advantage of not terminating these ports is that the…

Lees verderYAV91501 2,5GHz 50Ohm SMB Multiplexer (not terminated)

YAV90PNE CAN bus pneumatic sub-system

Features ? 10x 3-way pneumatic valves to directly control 10 simple or 5 double effect cylinders; ? 12 inputs for position sensors. ? Linear pressure sensor included ? 2 inlets for direct air inputs ? 4 digital outputs (24Vdc) to drive external coils ? 1 analog output to optionally control a proportional valve ? 2 digital inputs for output monitoring ? Controlled through CAN bus ? Power requirements: 24Vdc ? Automatic device identification ? National Instruments…

Lees verderYAV90PNE CAN bus pneumatic sub-system

YAV90CLR 16 channels Color meter for LED testing

? Test up to 16 LEDs (Low to High Brightness) simultaneously ? Fiber optic input channels (POF) ? 1 optical calibration RGB LED output ? Wave lengh (420?650 nm) and luminance (Intensity) readout ? 24VDC single power supply ? OK/NOK comparator threshold settings ? VPC receiver fixture compatible ? CAN bus control ? Built in power supply ? Self module identifier ? National Instruments LabView drivers Download the Catalogue. The YAV90CLR module is the most cost…

Lees verderYAV90CLR 16 channels Color meter for LED testing

YAV90ISP 8x Fast ISP and I2C/SPI Interface

? Interface for universal In-System Programmers up to 8 simultaneous targets in parallel ? Isolation relay barrier / De-multiplexer module to increase to up 32 devices ? Keeps extremely short wires for keeping signal integrity ? I2C and SPI communications interface Download the Catalog The YAV90ISP standalone in-site programming interface has been designed to simplify and standardize the wiring in testing platforms that use fast ISP and/or I2C / SPI data communications. All active lines, included…

Lees verderYAV90ISP 8x Fast ISP and I2C/SPI Interface

YAV90PIN 12 SPST 8A relays

Description ? 12 Relays 8A 250V ? Double tripaddle contact per connection. ? Plug-in terminals for power supplies and loads ? Enable contact for each relay ? Power supply of 24VDC only ? Automatic identification of the module ? National Instruments LabView drivers Download the Catalogue Applications ? Power Input/outputs in tests systems using VPC receivers. The YAV90PIN board is designed to cover the need to control the available power supplies in a test system to…

Lees verderYAV90PIN 12 SPST 8A relays

YAV90CIN 12 SPST 8A relays Current meas

Description ? 12 Relays 8A 250V ? Current measurement ? Double tripaddle contact per connection. ? Plug-in terminals for power supplies and loads ? Enable contact for each relay ? Power supply of 24VDC only ? Automatic identification of the module ? National Instruments LabView drivers Download the Catalogus [youtube https://www.youtube.com/watch?v=YTRr1BOvVPg?rel=0] Applications ? Power Input/outputs with current measurement in tests systems using VPC receivers

Lees verderYAV90CIN 12 SPST 8A relays Current meas

YAV9JTAG 128 DIOs JTAG BSRU

Fully open general application JTAG I/O Interface ? Board integration into the platform, therefore can be used for multiple fixtures ? Up to 128 tristate DIOs, 1V8/2V5/3V3 (5V tolerant), 8x 8bits AIs, 8x 8bits AOs and 2 RS232/UART ports (Set of two boards) ? Built-in USB 2.0 to JTAG interface ? Configurable JTAG chain till 40Mhz ? Connector input compatible with XJAG USB-JTAG Interface ? Automatic interface selection according to the fixture ? Working voltage automatic…

Lees verderYAV9JTAG 128 DIOs JTAG BSRU

YAV90071 6-GHz 50-Ohm 1x(1 to 4) Multiplexer

YAV90071 6-GHz 50-Ohm 1x(1 to 4) CanBus controlled Multiplexer Input Characteristics 6 GHz 50 Ohm MCX 1 to 4 Channels 30Vac/dc, 10W Max Max current 310mA Relay coil votage 24Vdc Absorbent RF Characteristics Characteristic impedance (Z0) 50 ? Insertion loss < 2.5 GHz < 1 dB Insertion loss < 4 GHz < 1,5 dB Insertion loss < 5 GHz < 6 dB Isolation < 5 GHz (Open contacts) > 50 dB Voltage standing rate ratio (VSWR)…

Lees verderYAV90071 6-GHz 50-Ohm 1x(1 to 4) Multiplexer